Radio Shack Pro 2055 Scanner Manual
Question About Radio Shack Scanner adv20004 user manual. I'm looking for a manual for a radio shack pro-2055 tripple trunking scanner.
Programming Shortcut pro-2055 Pro-2055 Cheat Sheet If system is Motorola Type II, EDACS or LTR start with Programming section, if Motorola Type I or IIi, set the.
Pro-97/2055 Scanner Manual: Last Updated May 30, 2015: Click here to buy a printed, bound, formatted in color, copy of this manual from Scanner Master.
Easier to Read Pro-97/2055 Scanner Manual Last Updated May 30, 2015 Click here to buy a printed, bound, formatted in color, copy of this manual from Scanner Master Contents These are another excellent set of radios that have many fine features for scanning and trunking. However, anyone who has tried to read the manuals that come with the radios know it can be a little hard (if you're lucky) to find, read, and figure out some of the steps, especially in the searching and trunking sections. IMHO they are a mess. I can’t remember everything and find myself referring back to the manual for explanations of procedures and find it frustrating trying to figure out the wording every time. I decided to write and publish this for myself to make it easier to use the radio and am happy to share it with you. This should also make it easier for most people to use some of the more advanced features of the radio (and get their money’s worth if you paid full-price for the radio new) as I will try to explain procedures a little more clearly and in a more logical order. Granted, these radios aren't simple so you will have to spend some time on them but this manual will at least make it easier. If you follow the red highlighted text in the programming sections, you should find what you need to know. If you want to find out what's really going on with the radio, read everything else. Some of the better features of these radios are the ability to receive tone codes in certain service searches, the seek feature in search mode that resumes searching after 5 seconds, and the adjustable ID delay. IDs can be locked out in open mode (vs. the older Pro-93/2053/94/95). The Skywarn lets you program 3 Skywarn frequencies (or any other conventional freqs) into channels 997-999 for one-touch access to them. The Repeater Finder Tool will help you find the correct LCN for LTR systems. The best one, in my opinion, is the ability to configure everything in the software, on the computer, and then just shoot it to the radio (with a one-way cable) or back to the computer (with a two-way cable). Much easier to work with the keyboard and see the monitor. You can set the attenuator globally or per channel. With a couple of keystrokes, you can view the IDs as text or code. There are 5 ID lists (30 IDs per list) to store 150 IDs for each bank. Now, on the flip side, there are some pretty annoying things about these radios too. They still have preset steps that will not tune to many of the splinter frequencies in the VHF range (except the 108-137 air band) like 151.0125; (it accepts it as 151.01). The Air service search is relatively slow because of the 8.33 kHz steps. Still only 1 priority channel? The backlight goes out long before the batteries die. An overview of the features can also be viewed at my Trunking Radio Comparison Chart page. You will also need a better antenna. The stock rubber duck isn't fabulous. RS has the Center-Loaded Telescoping Whip for $15 - better for VHF/UHF. The 800MHz Scanner Antenna for $25 - 100% better for 700+ MHz. You may be able to find others on the web but RS is convenient so you can buy it and take it back in the same day if you don't like it. Read the reviews for each at the site. These radios also have software that will enhance and/or enable other features not possible with just the keypad and have been noted when known. My opinion is get the software if you have a lot of frequencies. With all the features and setting in these new fangled devices it will save you hours of programming and frustration. It may also be easier to figure out the software than the keypad sequences. Alpha tagging is great but much easier with the software. Because of the limited amount of keys on the radios, programming a 3 letter word takes about 20 keystrokes on my Pro-97, if you can remember the sequence and don't make a mistake, after you program the bank name. See what I mean? Get the software. You have to dish out $20 bucks or so for a cable, the software is $20-30 (after a 30-day free trial), and there are plenty of newsgroups on the Net about these radios to help you hook up to the computer and work the software. All in all, they will compliment your scanner collection (provided you have one). I will assume you know how to obtain the basic information from the original manual such as following safety procedures, putting the batteries in, connecting the antenna, finding specs, etc. and concentrate on the main functions of the scanner. I hereby absolve myself from anything that happens to anyone or the scanner as a result of the information you will be reading. You are welcome to copy and/or print these pages and use them in the scanning hobby as long as you don't change, redistribute, or charge/accept money for them. Check back often as this document will be updated and revised from time to time. I have tried the best I can to make sure everything is accurate here but if I missed a step or you see something that's obviously wrong, please email me. Control Channel Only Scanning - automatically determines the trunking frequencies for Motorola trunking systems only, once the control channels are programmed. Repeater Finder Tool - displays the current Home Repeater when monitoring LTR transmissions in manual mode. Data Cloning - lets you transfer the programmed data from one Pro-97/2055 to another Pro-97/2055. You can also download the programmed data from a PC to the scanner (using an optional one-way PC cable), or upload the programmed data to the scanner (using a two-way PC cable) with the optional software. Simultaneous Trunk and Scan - scans conventional and trunked frequencies together at the same time. 16 Character, 4-line, Dot Matrix Text Display - lets you program a text label for each channel, bank, talkgroup ID, or a limit search so you can easily identify the transmission. Trunking ID Delay - variable delay (1/2 to 4 seconds) before searching for another talkgroup ID so you can hear more replies that are made on the same talkgroup ID. 6 Service Search Banks - Marine, CB, FRS/GMRS/MURS, Police/Fire, Aircraft, and Amateur pre-programmed search ranges and 1 programmable limit search to reduce search time and monitor interesting frequencies more quickly. Tune Search - The scanner will allow you to start searching up or down from a specific frequency. Search Lockouts- for each channel in the CB, Marine, and FRS/GMRS/MURS bands and 50 per band for each of the, Air, Police/Fire, Amateur, or limit search bands. Attenuation - lets you program your scanner (per channel or globally) to reduce the scanner's sensitivity to strong local signals or noise caused by these signals to reduce interference. 10 Channel Storage Banks - you can store up to 100 channels in each bank. HyperSearch and HyperScan - searches up to 100 steps per second and scans up to 50 channels per second. 10 ID-Storage Banks - lets you store and/or lock out 1500 IDs in 10 ID banks that have 5 sub-ID banks of 30 each. Each sub-bank can be turned on or off so you can monitor ID's you prefer. Channel Lockouts - lets you lock any channel in any bank. Weather Alert - can be set to automatically sound the alarm tone to advise of hazardous weather conditions when it detects the alert signal on the local National Oceanic and Atmospheric Administration (NOAA) weather channel (SAME standby mode) or you can also scan and set the weather channel as a priority channel. Displays the weather event text with four alert levels so you can see and hear the reason for the alert. Also has 3 programmable Skywarn channels. Triple-Conversion Circuitry - virtually eliminates (depending on your location) any interference from IF (intermediate frequency) images, so you hear only the selected frequency. Backlit Keypad and Display - select the time the light stays on or set to constant. Three Power Options (Pro 97) - lets you power the scanner using internal batteries; alkaline, Ni-Cad, or Ni-MH; external AC power using an optional 9 volt 300-mA AC adapter/charger (and RS ‘type C’ adaptaplug); or DC power using an optional 9 volt DC cigarette-lighter power cable. Scan/Search Delay - 2 second (adjustable delay with optional software and cable) scan and search delay before moving to another channel, frequency, or trunking system so you can hear more replies that are made on the same transmission. 1 Priority Channel - lets you program an additional frequency, one of the conventional channels, or a weather channel and then have the scanner check that channel every 2 seconds while it scans the bank, so you don't miss transmissions on that frequency or channel. Manual Access - lets you directly access any channel or frequency. Key Lock - lets you lock the scanner's keys to help prevent accidental changes to the scanner's programming. Battery Low Alert (Pro 97) - warns you when battery power gets low by beeping about every 10 seconds. Key Confirmation Tones - the scanner sounds a tone when you press a key, perform an operation correctly, and an error tone if you make an error. Can be turned off. Memory Backup - keeps the frequencies stored in memory for an extended time if the radio loses power. Scanning- the process of stepping through conventional channels in scan banks. Trunktracking (open mode)- the process of searching for all active talkgroup IDs in trunked systems, in scan banks. Trunkscanning (closed mode)- the process of stepping through programmed talkgroup IDs in ID lists, in trunked systems, in scan banks. Open and Closed Modes- You search all IDs in Open mode or just programmed IDs in Closed mode. Pause Mode- the mode the radio is in while paused on a scan; service, limit, or tune search. Searching- the process of searching for active frequencies in pre-programmed service searches, programmed frequency bands, or the limit search. Manual Mode- used for browsing and monitoring a channels. Program Mode- used for storing frequencies, limit searches, priority channels, trunking frequencies/systems/fleet maps, and talkgroup ID lists. Trunk Mode- used for trunking and programming trunking frequencies and functions. Clone Mode- used for cloning scanners and uploading/downloading to/from scanners using a computer. At certain times, the radio can be in more than one mode at a time such as program and trunk mode to program trunked functions. Trunking systems let a large group of 2-way radio users (or even different groups of 2-way radio users) efficiently use a set of frequencies. Instead of selecting a specific frequency for a transmission, the user’s radio selects a programmed trunking bank in the system when that user presses their PTT (push to talk) button. The trunking system automatically transmits the call on the first available frequency, and also sends (on a different frequency called a Data or Control channel) a code that uniquely identifies that transmission as a talkgroup ID (or just ID.) So when you are trunktracking a system, you are listening to active IDs transmitting in the system (each using the first available frequency in the system.) Trunking systems in general allocate and use fewer frequencies among many different users. Since the trunking system might send a call and its response on different frequencies, it is difficult to listen to trunked communications using a conventional scanner. These scanners let you monitor the control channel frequency so you can hear calls and responses for users and more easily "follow" conversations than with a conventional scanner. These scanners trunktrack the following types of systems: Motorola Type I or Type IIi systems require you to program a fleet map. This allows you to receive the talkgroup IDs correctly. If you don’t know which fleet map to use, you can try a method I found at Radio Reference.com.. Since it is rather lengthy, I will just give you the link. Determining Type I Motorola Fleet Maps by Dave Goodson. If you know the fleet map by name, E1P1, E1P2, etc., I have listed 16 pre-set fleet maps so you can see the size codes. 1. In Manual mode select any channel in the bank you want to program the fleet map in (Ex: 001) then press MAN to advance to the channel. 2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list and MOT: none. Thanks to Radio Reference.com for most of this information. Programming the Offset and Base Frequency To properly track Motorola UHF-lo (406-512 MHz) trunked systems, you must program the applicable offset and base frequency for each system. This can be done after you program the trunking frequencies and system. If you don't know the offset and base frequency, I have found an explanation at the Trunked Radio Systems User’s Page. Look for 'Determining Base and Offset Frequencies for the BC245xlt' by John C. There is a similar explanation at Radio Reference. 1. In Manual mode select any channel in the bank containing the UHF system by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. 2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list. 3. Press MODE. MOT: none should appear in the display. 4. Press FUNC then 2. You will see the current settings for the base frequency, offset, and step size. While B in Base is blinking, enter the base frequency then press ENT. Press ENT again to confirm and move down to the Offset setting. Or, if the entry is correct, press ENT to move down. 5. While O in Offset is blinking, enter the offset then press ENT. Press ENT again to confirm and move down to the Step setting. Or, if the entry is correct, press ENT to move down. 6. While S in Step is blinking, press or to select the step then press ENT to confirm and exit. Or, if the entry is correct, press ENT to exit. Press MAN to exit programming or SCAN to start scanning. You have to set the ID delay for the bank to pause on an ID before scanning resumes. Setting the scan delay for the channel has no effect on an ID. The delay can only be set for the whole bank, not an individual ID. When activated, the ID delay watches the control channel command for the delay time when the signal disappears from the voice channel. 1. In Manual mode select any channel of the bank you want to turn a list on or off in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. 2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the ID list. 3. Press FUNC then DELAY. Use Up/Down keys to set ID delay appears in the display. 4. Press or to change the delay then press ENT to store the setting. Press MAN to exit programming. To View the ID or Text Tag for the ID, quickly press TEXT while any ID in the bank is displayed. Press TEXT again while any ID in the bank is displayed to revert. To turn ID lists on or off (in closed mode only), quickly press FUNC then TRUNK while an ID is displayed. 'ID Banks:' and the lists that are turned on will appear as numbers on the 3rd line when transmissions are received. The cursor will blink on the list number that has the receiving ID. If the list is turned off a . (dot) will replace the number. Quickly press FUNC then the list number while receiving to turn the list on or off. (Yeah, right, real simple). Quickly press FUNC then TRUNK while an ID is displayed to get rid of the 'ID Banks:' selection line. Or, See Turning ID Lists Off and On to do it in Manual mode before scanning. To exit trunking and scanning, press MAN. While trunking, you may not know which agency, fleet, or talk group the talk group IDs are assigned to until you listen a while. You can determine the type of agency you are listening to after a short while by matching the IDs with the transmission you hear. You can then program them into ID lists. See Programming Talk Group IDs. Determining the service associated with a talk group ID might take awhile but finding IDs is half the fun. 1. In Manual mode select any channel of the bank you want to turn a list on or off in by entering the bank number and channel number (Ex: 001) then press MAN to advance to the channel. 2. Press PGM then TRUNK to put the scanner in program and trunk modes. You will see the bank number (0-9), list number (0-4), and the list status (ON or OFF) on the 1st line, the ID# in the list (0-29) on the 2nd line, the ID on the 3rd line, and bank tag on the 4th line (if programmed). 3. Press TRUNK (each time) to select one of the ID lists (0-4) to turn on or off. 4. Press FUNC then 1 to turn the list on or off. Press SCAN or MANUAL to exit.
Easier to Read Pro-97/2055 Scanner Manual
PRO 2055 SCANNER MANUAL Did you searching for Pro 2055 Scanner Manual? This is the best place to read pro 2055 scanner manual before service or repair your product.
The Pro-2055 was manufactured for Radio Shack by GRE America Inc The same scanner as the Pro-97 but as a base/mobile. Trunk tracker three technology.
Radio shack Pro 2055 Pdf User Manuals. View online or download Radio shack Pro 2055 Manual.
Owner’s Manual Cat. No. 20-430 PRO-2050 VHF/UHF/Air/800MHz 300-Channel TrunkTracker Home Scanner Please read before using this equipment. 20-430.fm Page 1 Wednesday.
Painstakingly created by Marksscanners, this 48 page Easier to Read Scanner Manual takes you deep into the amazing feature set and instructions for their two original.